Trixter X-Bike Manuale Utente

7 Adjusting the Bike Seat Adjustment 1. Rotate the pedals so that one of the pedals is in the upward position. 2. Place your foot in the toe clip o

8 Minor Cable Adjuster Cable Release Bolt 2. Using a 6mm Hex key, loosen the bolt at the bottom of

9 USING YOUR X-BIKE INDOOR PERFORMANCE BIKE WARNING SAFETY FIRST – PLEASE REFER TO THE SAFETY INFORMATION ON PAGES 1 & 2 OF

10 Mounting and Dismounting Once sitting comfortably on the Bike, make sure to tighten each toe strap securely before commencing exercise. Dismount

11 MAINTENANCE INSTRUCTIONS Helpful Hints The safety level given by the design of X-Bike™ Indoor Performance Bike can only be maintained when the eq

12 Preventative Maintenance Refer to the appropriate Parts Removal and Replacement section on PAGES 19-28 for all disassembly and assembly instructio

13 Minor Cable Adjuster Cable Release Bolt o Turn the Grip-shift™ fully clockwise to the minimum res

14 Examine the damper for smoothness and consistency of movement. This is determined by testing the movement in the handlebars firstly in minimum and

15 Dryness or prolonged use may cause the height and reach adjustments for the bars and seat to become tight. If this is the case, the sliding assembl

16 PARTS – REMOVAL AND REPLACEMENT WARNING: It is vitally important to keep the X-Bike Indoor Cycle properly maintained but if you are unsure about

17 Bolt 1 Bolt 2 Bolt 3 2. Turn the right hand crank arm vertically downwards as this

18 until the chain slack is eliminated and the flywheel can rotate freely without pulling the pedals around with it. Replacing the Handlebars 1. NO

19 2. Using a 6mm hex key, loosen the bolt at the bottom of the V-Brake to release the resistance cable. 3. Pull the resistance cable out of the ass

20 Right Crank Arm 1. Follow procedures for “Removing the Chain Guard” above. 2. Use an 8mm Hex key to remove the pedal crank bolt. 3. Thr

21 Removing Pedals 1. Block the crank arm from spinning, and use a bicycle pedal wrench (15mm) on the pedal nut to remove the pedal from the crank

22 Rear Bolts 2. Undo the Top Covers – at the front and rear by using a 4mm extended hex key. Carefully lift the top cover (front and re

23 6. Locate the fixed end of the damper into the bracket on the assembly and fit the nut. Tighten securely. 7. Tighten the moving end securely. 8.

24 Replacing the “Return to Zero” Springs 1. Remove the top cover as directed in the covers removal section. 2. Using the spring fitting tool, inse

25 c. The spring pillars - apply some grease to each of the spring loops where they are in contact with the spring pillars. Manoeuvre the mechanism l

26 Replacing the Centre Slider 1. Remove the top and side covers as directed in the covers removal section. 2. Using an 8mm Hex head, undo the bolt

TABLE OF CONTENTS Safety Information ………………………………………… Page 1 Introduction…………………………………………… Page 3 X-Bike™ Indoor Performance Bike X-Biking™

27 EQUIPMENT AND TECHNICAL INFORMATION Please refer to Illustrations on Pages 30 to 32 for more information X-Bike Frame Specifications Frame Tubu

28 Exploded View & Parts Identification 1 FRAME 8-1 SEAT 2-1 FRONT BASE LEG 8-2 SEAT POST 2-2 REAR BASE LEG 8-3 S

29 X-Bars Exploded View

30 X-Bars Parts Identification Table ID PART NUMBER QTY PART DESCRIPTION 1 1283-BP6300-001 1 BP63 147.2X46XT14 A6061-T6 ANOD 2 1282-AX1Y00-001

31 X-Bike Indoor Performance Bike FEATURES Structure X-BIKE™ Indoor Performance Bike o High strength attractive tubular and elliptical steel X-bik

32 o 4-bolt clamp handlebar clamp to provide a very secure bar fitment. o Boxer Bar ends o Handlebar Grips – Hi grip rubber compound. o Non-corro

33 riders from below 5’ (1.5m) to 7’ (2.15M) tall. Laser etched reference marks on the seat post make resetting a favorite position easy. o Saddle T

34 o V-Brake mechanism is fitted below the flywheel, well out of sweat zone for increased longevity and ease of maintenance. o Chain guard to protec

35 THANK YOU FOR PURCHASING AN X-BIKE INDOOR PERFORMANCE BIKE PLEASE TAKE A FEW MORE MINUTES TO READ OUR WARRANTY POLICY (PAGE

36 LIMITED WARRANTY Trixter North America, Inc. and Trixter Europe Limited (“Trixter”) warrant the frame of each new indoor cycle to be free from de

1 SAFETY INFORMATION WARNING TO AVOID DEATH OR SERIOUS PERSONAL INJURY • BEFORE beginning any fitness or conditioning program, consult with your

37 WARRANTY REGISTRATION CARD Thank you for purchasing this X-Bike Indoor Performance Bike. The Owners’ Manual contains important information for p

38 Dear new X-Bike™ Performance Indoor Bike Owner: This is the backside of the Warranty Registration Card. If you have not completed the Warran

39 INDEX Adjustment 10 Assembling the X-Bike Indoor Performance Bik

40

2 • NEVER exceed the weight limit for this bike. The weight limit for this bike is 300 pounds. Do not use the X-Bike™ Indoor Performance Bike if your

3 INTRODUCTION X-Bike™ Indoor Performance Bike Congratulations on purchasing your Trixter Enabled X-Bike™ Indoor Performance Bike, one of the most

4 INSTALLATION & ADJUSTMENT SETTING UP THE X-BIKE Indoor Performance Cycle WARNING NOTE THAT THE SAFETY INFORMATION ON PAGES 1 & 2 SHOULD

5 B. Assembling the Bike All references to the right or left side and to the front or back are made as if you were sitting on the exercise bike read

6 Insert the 4 x M8 bolts provided through the base plate of the X-Bars into the adaptor from front towards the rear, and ensure that a washer is fitt